Forums

another strange board

Started by Unknown November 20, 2021
mandag den 22. november 2021 kl. 00.00.42 UTC+1 skrev Clifford Heath:
> On 22/11/21 5:06 am, jla...@highlandsniptechnology.com wrote: > > On Sun, 21 Nov 2021 07:47:21 -0800 (PST), Lasse Langwadt Christensen > > <lang...@fonz.dk> wrote: > > > >> s&oslash;ndag den 21. november 2021 kl. 02.47.11 UTC+1 skrev jla...@highlandsniptechnology.com: > >>> https://www.dropbox.com/s/do0k7ystcmmu1xg/T502A4.jpg?raw=1 > >>> > >> > >> can you actually get a v-score made that doesn't go all the way across the board? > > > > Can't see why not. We'll buy from the board house that will. > Each snap must go right across the remaining board, or they can't snap > it. Any v-score will run a bit past its notional end-point, and mustn't > run into another board. > > That's possible to ensure by insisting on the scores running across the > board.
but it seems they can run part way https://youtu.be/orwKNB02Ado?t=30
On Mon, 22 Nov 2021 10:00:34 +1100, Clifford Heath
<no.spam@please.net> wrote:

>On 22/11/21 5:06 am, jlarkin@highlandsniptechnology.com wrote: >> On Sun, 21 Nov 2021 07:47:21 -0800 (PST), Lasse Langwadt Christensen >> <langwadt@fonz.dk> wrote: >> >>> s&#2013266168;ndag den 21. november 2021 kl. 02.47.11 UTC+1 skrev jla...@highlandsniptechnology.com: >>>> https://www.dropbox.com/s/do0k7ystcmmu1xg/T502A4.jpg?raw=1 >>>> >>> >>> can you actually get a v-score made that doesn't go all the way across the board? >> >> Can't see why not. We'll buy from the board house that will. > >Each snap must go right across the remaining board, or they can't snap >it. Any v-score will run a bit past its notional end-point, and mustn't >run into another board. > >That's possible to ensure by insisting on the scores running across the >board.
Sorry, I don't understand that. We will buy single boards, not panels, so we can easily separate the little fixturing wings after pick-and-place. The PCB house won't brickwall boards on their panel because they route them apart. We slice the v-scores on our big pizza cutter, not bend and snap. -- Father Brown's figure remained quite dark and still; but in that instant he had lost his head. His head was always most valuable when he had lost it.
On 22/11/21 10:20 am, Lasse Langwadt Christensen wrote:
> mandag den 22. november 2021 kl. 00.00.42 UTC+1 skrev Clifford Heath: >> On 22/11/21 5:06 am, jla...@highlandsniptechnology.com wrote: >>> On Sun, 21 Nov 2021 07:47:21 -0800 (PST), Lasse Langwadt Christensen >>> <lang...@fonz.dk> wrote: >>> >>>> s&oslash;ndag den 21. november 2021 kl. 02.47.11 UTC+1 skrev jla...@highlandsniptechnology.com: >>>>> https://www.dropbox.com/s/do0k7ystcmmu1xg/T502A4.jpg?raw=1 >>>>> >>>> >>>> can you actually get a v-score made that doesn't go all the way across the board? >>> >>> Can't see why not. We'll buy from the board house that will. >> Each snap must go right across the remaining board, or they can't snap >> it. Any v-score will run a bit past its notional end-point, and mustn't >> run into another board. >> >> That's possible to ensure by insisting on the scores running across the >> board. > > but it seems they can run part way > > https://youtu.be/orwKNB02Ado?t=30
Yes. But I was giving a reason why some board houses won't do that.
jlarkin@highlandsniptechnology.com wrote:

> We slice the v-scores on our big pizza cutter, not bend and snap.
But still, why not a slot? This is a standard feature. Best regards, Piotr
On Mon, 22 Nov 2021 09:33:03 +0100, Piotr Wyderski
<bombald@protonmail.com> wrote:

>jlarkin@highlandsniptechnology.com wrote: > >> We slice the v-scores on our big pizza cutter, not bend and snap. > >But still, why not a slot? This is a standard feature. > > Best regards, Piotr
Well, a lot of slots with tabs to cut. That's harder to draw. It could give me a smooth edge for the monitor connector, but that's only 1 GHz so doesn't care much. -- Father Brown's figure remained quite dark and still; but in that instant he had lost his head. His head was always most valuable when he had lost it.
On Sun, 21 Nov 2021 17:28:33 +0000, TTman <kraken.sankey@gmail.com>
wrote:

>On 21/11/2021 15:47, Lasse Langwadt Christensen wrote: >> s&#2013266168;ndag den 21. november 2021 kl. 02.47.11 UTC+1 skrev jla...@highlandsniptechnology.com: >>> https://www.dropbox.com/s/do0k7ystcmmu1xg/T502A4.jpg?raw=1 >>> >> >> can you actually get a v-score made that doesn't go all the way across the board? >> > >Err no...
Royal Circuits says yes. The others haven't replied yet. -- If a man will begin with certainties, he shall end with doubts, but if he will be content to begin with doubts he shall end in certainties. Francis Bacon
On Sat, 20 Nov 2021 17:47:03 -0800, jlarkin@highlandsniptechnology.com
wrote:

>https://www.dropbox.com/s/do0k7ystcmmu1xg/T502A4.jpg?raw=1 > >The real action is in the upper-right, 0.8 square inches. I had to lay >that out myself because it's too hard to explain to anyone else. > >The Brat did the rest of the layout. > >Production wants the wings on the sides for fixturing. After the parts >are stuffed, we can lop them off.
I think it's done. Resequenced and ready to go. https://www.dropbox.com/s/pz6tszau9lsi403/T502A8.jpg?raw=1 I converted the v-scores (with great effort) to slots, and then manufacturing made me make them back into v-scores. -- If a man will begin with certainties, he shall end with doubts, but if he will be content to begin with doubts he shall end in certainties. Francis Bacon