>>>
> >> I have a 24v DC motor that I'm using with a PWM controller supplied by a
> >> 24v SMPS. I want to be able to briefly switch the motor to 48v with a
> >> relay.
>
> > ** Bad idea.
> > Doubling the DC input to a brush motor will quickly destroy it - it may last only a few minutes of such abuse.
> > Over voltage creates severe acing across the segments of the commutator.
> >
> > A good rule is to have no more than 2.5V for each pole of a DC motor.
> >
> >
> Phil thanks - I didn't know that. Nevertheless I'm going to proceed
> with my arrangement:
** So you did not want our advice - did you ?
> - it's for my own use & not a customer's, nor a product
> - the "briefly" is 5-10 seconds and a duty cycle of maybe 5-10%
> - I have a few of these motors and if one is destroyed I'll use another
> and have learned a lesson
** Did you count how may poles on that motor?
It matters just a tiny bit ......
..... Phil
Reply by Bob Engelhardt●October 21, 20212021-10-21
On 10/11/2021 7:10 PM, Phil Allison wrote:
> bobenge...@gmail.com wrote:
> ===========================
>>
>> I have a 24v DC motor that I'm using with a PWM controller supplied by a
>> 24v SMPS. I want to be able to briefly switch the motor to 48v with a
>> relay.
>
> ** Bad idea.
> Doubling the DC input to a brush motor will quickly destroy it - it may last only a few minutes of such abuse.
> Over voltage creates severe acing across the segments of the commutator.
>
> A good rule is to have no more than 2.5V for each pole of a DC motor.
>
>
> ..... Phil
>
Phil thanks - I didn't know that. Nevertheless I'm going to proceed
with my arrangement:
- it's for my own use & not a customer's, nor a product
- the "briefly" is 5-10 seconds and a duty cycle of maybe 5-10%
- I have a few of these motors and if one is destroyed I'll use another
and have learned a lesson
Reply by ehsjr●October 15, 20212021-10-15
On 10/11/2021 1:39 PM, Bob Engelhardt wrote:
> I have a 24v DC motor that I'm using with a PWM controller supplied by a
> 24v SMPS. I want to be able to briefly switch the motor to 48v with a
> relay. I don't have a 48v supply, but I do have a 24v transformer &
> bridge. I know that the following will give me the 48v,
Your 24V xformer + bridge will give you peaks of
over 36 V
Ed
and I think
> that the Motor Control will be OK with it. But I'd like to know if I'm
> missing something. The relay will disconnect the Motor Control from the
> motor before connecting the 48v.
>
> Thanks, Bob
>
> ___________________________ +48v
> _________ | _________
> | +|______________|______| Motor |_____
> | 24vdc | |Control|
> | SMPS | | |
> | -|_______________._____| |_____ Motor
> |_______| | |_______|
> |
> _________ _________ |
> | 24v |____| Full +|__|
> |Xformer| | wave |
> | | |bridge |
> | |____| -|________________________________
> |_______| |_______|
Reply by amdx●October 13, 20212021-10-13
On 10/11/2021 6:10 PM, Phil Allison wrote:
> bobenge...@gmail.com wrote:
> ===========================
>> I have a 24v DC motor that I'm using with a PWM controller supplied by a
>> 24v SMPS. I want to be able to briefly switch the motor to 48v with a
>> relay.
> ** Bad idea.
> Doubling the DC input to a brush motor will quickly destroy it - it may last only a few minutes of such abuse.
> Over voltage creates severe acing across the segments of the commutator.
>
> A good rule is to have no more than 2.5V for each pole of a DC motor.
>
>
> ..... Phil
>
I had a 28V 2hp motor on a go cart and ran it on 48V. Ran it for a few
years, and never saw any commutator problem.
But we did have an especially long, hard run and it came back with the
windings smoking. It would draw over 250 amps untill you got up to speed.
I will admit it was a motor designed for a military application, so
probably had some good specs.
Mikek
--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
>
> I have a 24v DC motor that I'm using with a PWM controller supplied by a
> 24v SMPS. I want to be able to briefly switch the motor to 48v with a
> relay.
** Bad idea.
Doubling the DC input to a brush motor will quickly destroy it - it may last only a few minutes of such abuse.
Over voltage creates severe acing across the segments of the commutator.
A good rule is to have no more than 2.5V for each pole of a DC motor.
..... Phil
Reply by Bob Engelhardt●October 11, 20212021-10-11
I have a 24v DC motor that I'm using with a PWM controller supplied by a
24v SMPS. I want to be able to briefly switch the motor to 48v with a
relay. I don't have a 48v supply, but I do have a 24v transformer &
bridge. I know that the following will give me the 48v, and I think
that the Motor Control will be OK with it. But I'd like to know if I'm
missing something. The relay will disconnect the Motor Control from the
motor before connecting the 48v.
Thanks, Bob
___________________________ +48v
_________ | _________
| +|______________|______| Motor |_____
| 24vdc | |Control|
| SMPS | | |
| -|_______________._____| |_____ Motor
|_______| | |_______|
|
_________ _________ |
| 24v |____| Full +|__|
|Xformer| | wave |
| | |bridge |
| |____| -|________________________________
|_______| |_______|