Electronics-Related.com

Modeling Gate Drive Diodes

Jason Sachs March 11, 20241 comment

This is a short article about how to analyze the diode in some gate drive circuits when figuring out turn-off characteristics --- specifically, determining the relationship between gate drive current and gate voltage during turn-off of a power transistor.


A New Related Site!

Stephane Boucher September 22, 20222 comments

We are delighted to announce the launch of the very first new Related site in 15 years!  The new site will be dedicated to the trendy and quickly growing field of Machine Learning and will be called - drum roll please - MLRelated.com.

We think MLRelated fits perfectly well within the “Related” family, with:

  • the fast growth of TinyML, which is a topic of great interest to the EmbeddedRelated community
  • the use of Machine/Deep Learning in Signal Processing applications, which is of...

The DSP Online Conference - Right Around the Corner!

Stephane Boucher September 20, 20201 comment

It is Sunday night as I write this blog post with a few days to go before the virtual doors of the very first DSP Online Conference open..

It all started with a post in the DSPRelated forum about three months ago.  We had just had a blast running the 2020 Embedded Online Conference and we thought it could be fun to organize a smaller event dedicated to the DSP community.  So my goal with the post in the forum was to see if...


Already 3000+ Attendees Registered for the Upcoming Embedded Online Conference

Stephane Boucher February 14, 2020

Chances are you already know, through the newsletter or banners on the Related sites, about the upcoming Embedded Online Conference.

Chances are you also already know that you have until the end of the month of February to register for free. 

And chances are that you are one of the more than 3000 pro-active engineers who have already registered.

But If you are like me and have a tendency to do tomorrow what can be done today, maybe you haven't registered yet.  You may...


Part 11. Using -ve Latency DSP to Cancel Unwanted Delays in Sampled-Data Filters/Controllers

Steve Maslen June 18, 201918 comments
This final article in the series will look at -ve latency DSP and how it can be used to cancel the unwanted delays in sampled-data systems due to such factors as Nyquist filtering, ADC acquisition, DSP/FPGA algorithm computation time, DAC reconstruction and circuit propagation delays.

Some applications demand zero-latency or zero unwanted latency signal processing. Negative latency DSP may sound like the stuff of science fiction or broken physics but the arrangement as...


Somewhat Off Topic: Deciphering Transistor Terminology

Rick Lyons May 28, 20194 comments

I recently learned something mildly interesting about transistors, so I thought I'd share my new knowledge with you folks. Figure 1 shows a p-n-p transistor comprising a small block of n-type semiconductor sandwiched between two blocks of p-type semiconductor.

The terminology of "emitter" and "collector" seems appropriate, but did you ever wonder why the semiconductor block in the center is called the "base"? The word base seems inappropriate because the definition of the word base is:...


Free Goodies from Embedded World - Full Inventory and Upcoming Draw Live-Streaming Date

Stephane Boucher March 22, 20191 comment

Chances are that you already know that I went to Embedded World a few weeks ago and came back with a bag full of "goodies".  Initially, my vision was to do a single draw for one person to win it all, but I didn't expect to come back with so much stuff and so many development kits.   Based on your feedback, it seems like you guys agree that It wouldn't make sense for one person to win everything as no-one could make good use of all the boards and there would be lots of...


Free Goodies from Embedded World - What to Do Next?

Stephane Boucher March 6, 20194 comments

I told you I would go on a hunt for free stuff at Embedded World in order to build a bundle for someone to win.


Back from Embedded World 2019 - Funny Stories and Live-Streaming Woes

Stephane Boucher March 1, 20191 comment

When the idea of live-streaming parts of Embedded World came to me,  I got so excited that I knew I had to make it happen.  I perceived the opportunity as a win-win-win-win.  

  • win #1 - Engineers who could not make it to Embedded World would be able to sample the huge event, 
  • win #2 - The organisation behind EW would benefit from the extra exposure
  • win #3 - Lecturers and vendors who would be live-streamed would reach a (much) larger audience
  • win #4 - I would get...

Spread the Word and Run a Chance to Win a Bundle of Goodies from Embedded World

Stephane Boucher February 21, 2019

Do you have a Twitter and/or Linkedin account?

If you do, please consider paying close attention for the next few days to the EmbeddedRelated Twitter account and to my personal Linkedin account (feel free to connect).  This is where I will be posting lots of updates about how the EmbeddedRelated.tv live streaming experience is going at Embedded World.

The most successful this live broadcasting experience will be, the better the chances that I will be able to do it...


How to Read a Power MOSFET Datasheet

Jason Sachs September 15, 201514 comments

One of my pet peeves is when my fellow engineers misinterpret component datasheets. This happened a few times recently in separate instances, all involving power MOSFETs. So it’s time for me to get on my soapbox. Listen up!

I was going to post an article on how to read component datasheets in general. But MOSFETs are a good place to start, and are a little more specific. I’m not the first person to write something about how to read datasheets; here are some other good...


Thermistor signal conditioning: Dos and Don'ts, Tips and Tricks

Jason Sachs June 15, 201118 comments

In an earlier blog entry,  I mentioned this circuit for thermistor signal conditioning:

It is worth a little more explanation on thermistor signal conditioning; it's something that's often done poorly, whereas it's among the easiest applications for signal conditioning.

The basic premise here is that there are two resistors in a voltage divider: Rth is the thermistor, and Rref is a reference resistor. Here Rref is either R3 alone, or R3 || R4, depending on the gain...


Analog-to-Digital Confusion: Pitfalls of Driving an ADC

Jason Sachs November 19, 20118 comments

Imagine the following scenario:You're a successful engineer (sounds nice, doesn't it!) working on a project with three or four circuit boards. More than even you can handle, so you give one of them over to your coworker Wayne to design. Wayne graduated two years ago from college. He's smart, he's a quick learner, and he's really fast at designing schematics and laying out circuit boards. It's just that sometimes he takes some shortcuts... but in this case the circuit board is just something...


Byte and Switch (Part 1)

Jason Sachs April 26, 201114 comments

Imagine for a minute you have an electromagnet, and a microcontroller, and you want to use the microcontroller to turn the electromagnet on and off. Sounds pretty typical, right?We ask this question on our interviews of entry-level electrical engineers: what do you put between the microcontroller and the electromagnet?We used to think this kind of question was too easy, but there are a surprising number of subtleties here (and maybe a surprising number of job candidates that were missing...


10 Circuit Components You Should Know

Jason Sachs November 27, 20113 comments

Chefs have their miscellaneous ingredients, like condensed milk, cream of tartar, and xanthan gum. As engineers, we too have quite our pick of circuits, and a good circuit designer should know what's out there. Not just the bread and butter ingredients like resistors, capacitors, op-amps, and comparators, but the miscellaneous "gadget" components as well.

Here are ten circuit components you may not have heard of, but which are occasionally quite useful.

1. Multifunction gate (


Back from Embedded World 2019 - Funny Stories and Live-Streaming Woes

Stephane Boucher March 1, 20191 comment

When the idea of live-streaming parts of Embedded World came to me,  I got so excited that I knew I had to make it happen.  I perceived the opportunity as a win-win-win-win.  

  • win #1 - Engineers who could not make it to Embedded World would be able to sample the huge event, 
  • win #2 - The organisation behind EW would benefit from the extra exposure
  • win #3 - Lecturers and vendors who would be live-streamed would reach a (much) larger audience
  • win #4 - I would get...

Already 3000+ Attendees Registered for the Upcoming Embedded Online Conference

Stephane Boucher February 14, 2020

Chances are you already know, through the newsletter or banners on the Related sites, about the upcoming Embedded Online Conference.

Chances are you also already know that you have until the end of the month of February to register for free. 

And chances are that you are one of the more than 3000 pro-active engineers who have already registered.

But If you are like me and have a tendency to do tomorrow what can be done today, maybe you haven't registered yet.  You may...


Feedback Controllers - Making Hardware with Firmware. Part 10. DSP/FPGAs Behaving Irrationally

Steve Maslen November 22, 2018

This article will look at a design approach for feedback controllers featuring  low-latency "irrational" characteristics to enable the creation of physical components such as transmission lines. Some thought will also be given as to the capabilities of the currently utilized Intel Cyclone V, the new Cyclone 10 GX and the upcoming Xilinx Versal floating-point FPGAs/ACAPs.    

Fig 1. Making a Transmission Line, with the Circuit Emulator

 

Additional...


How to Estimate Encoder Velocity Without Making Stupid Mistakes: Part II (Tracking Loops and PLLs)

Jason Sachs November 17, 201312 comments

Yeeehah! Finally we're ready to tackle some more clever ways to figure out the velocity of a position encoder. In part I, we looked at the basics of velocity estimation. Then in my last article, I talked a little about what's necessary to evaluate different kinds of algorithms. Now it's time to start describing them. We'll cover tracking loops and phase-locked loops in this article, and Luenberger observers in part III.

But first we need a moderately simple, but interesting, example...


Lost Secrets of the H-Bridge, Part IV: DC Link Decoupling and Why Electrolytic Capacitors Are Not Enough

Jason Sachs April 29, 20147 comments

Those of you who read my earlier articles about H-bridges, and followed them closely, have noticed there's some unfinished business. Well, here it is. Just so you know, I've been nervous about writing the fourth (and hopefully final) part of this series for a while. Fourth installments after a hiatus can bring bad vibes. I mean, look what it did to George Lucas: now we have Star Wars Episode I: The Phantom Menace and