Sign in

username:

password:



Not a member?

Search Sci.Electronics.Design



Search tips

design by Keywords

8051 | Amplifier | AVR | CMOS | Converter | DAC | Diode | FPGA | GPS | I2C | IDE | Laser | LCD | MOSFET | Op-amp | Oscillator | Oscilloscope | PID | PLL | PSU | PWM | RFID | RS232 | RS485 | SMPS | Spice | Transformer | Transistor | TTL | USB | VCO

Ads

See Also

DSPEmbedded SystemsFPGA

Sci.Electronics.Design


Sci.Electronics.Design is a worldwide Usenet news group that is used to discuss various aspects of Electronic Circuit Design.

There are 5027 threads in our archives.

You are looking at page 13 of 503.

The threads with the newest articles are listed first.

generator problem [14 articles]

Jon - 2010-02-27 14:37:00
I'm trying to wire a transfer circuit for a generator. The generator will be located in the barn. The electrical service is at the house. Two 120vac wires and a ground go to the barn. There is...generator problem

Litz wire [88 articles]

Tim Williams - 2010-02-27 12:12:00
Who sells this stuff (without paying for miles at a time)? I'm especially interested in stupid thick stuff, like, as large as 8AWG equivalent. Nebraska Surplus for instance doesn't stock wire li...Litz wire

Posting for a friend, WAV file question [5 articles]

2010-02-27 10:01:00
Ok, a friend of mine recorded some 1970s FM telemetry data onto a digital tape and imported it as wave. Its 9.0 to 19.6 Khz sorta a hybrid between a triangle wave and a sine, It started out as a ...Posting for a friend, WAV file question

CD4046 Question [24 articles]

Chris - 2010-02-27 00:01:00
The data sheet just gives some ancient reference for finding the values for R1, R2, and C1. Is the RC network for the VCO is (R1, R2, C1)? Would I just use the cutoff frequency for the R1 and C2...CD4046 Question

1 GHz synthesizer [37 articles]

Andrew Holme - 2010-02-26 22:43:00
I'm developing a 1 GHz fractional-N synthesizer. The reference input is a 50 MHz sine wave which I'm converting to LVDS as follows: 1. 50 MHz sine wave arrives at board mounted SMA in 50-ohm sys...1 GHz synthesizer

Optimal Faraday cage [21 articles]

Edward Quinn - 2010-02-26 20:42:00
I need a quiet environment for operating test instruments. Needs to be as close to full spectrum as practical, and about 1.5 metres square or equivalent internal space. From what I have read, th...Optimal Faraday cage

RJ-45 "through wire" crimp connectors? [11 articles]

Sparky - 2010-02-26 19:45:00
I remember seeing RJ-45 (cat 5 I think they were) crimp connectors that had holes for the conductors drilled entirely through the connector such that each conductor could be fed out the end. After...RJ-45

H Bridge Driver for Single Coil, How to add protection? [3 articles]

Myauk - 2010-02-26 18:11:00
Dear All, I am designing H-Bridge Relay Circuit. The coil resistance is 36 ohms. Inductance is 500mH measured at 100Hz, 1V pk to pk with Agilent LCR Meter. Do I need additional snubber or TV...H Bridge Driver for Single Coil, How to add protection?

OT: Free download manager with auto download start etc. [4 articles]

pimpom - 2010-02-26 17:27:00
Sorry about the OT post. It belongs in alt.comp.freeware and I posted there, but there's no reply so far. This is what it's about: Can anyone please recommend a free download manager for Window...OT: Free download manager with auto download start etc.

One Stop IT Solutions Center - NiTM [2 articles]

NITMTECH - 2010-02-26 17:01:00
Dear Sir / Madam, Contact Us : Sathish Kumar HP: +65 9672 4662 /Tel Fax - 65 6220 1667 NiTM Technologies Pte Ltd, ( www.NiTMTech.com ) is Your One Stop IT Solutions Center. We highly focus the b...One Stop IT Solutions Center - NiTM
previous | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | next