 |
Search Sci.Electronics.Basics |
|
|
|
|
|
|
 |
|
|
Sci.Electronics.Basics -> LED Circuit?
There are 2 messages in this thread.
You are currently looking at messages 1 to 2.
|
Author: DrewDate: 13:28 14-03-08
|
|
I'm trying to apply a tally light system: a Panasonic video switcher
that sends a signal, and I want a couple of LEDs to turn on 150ft.
away whenever that signal is on. That's it.
Whether I'm building it myself or not, I need to understand what the
switcher does and doesn't handle, so I don't overload any of the
Panasonic's components - it's a $11,000 device. Here's the information
I have about its (D-sub15) control output:
http://www.drewlahat.com/misc/AV-HS400N_tally.GIF
Is it designed to drive LEDs directly, or would you recommend a relay?
What should also be in there to protect the unit (diodes)?
The signal has to go through 150 ft. of 26 AWG (7x34) Stranded TC
wire, rated at 38.5 ohm/Mft.
I might be able to use an off-the-shelf tally system - Datavideo TB5
(http://www.datavideo.us/products/TB_5_main_page.htm). Since it's
designed to connect to their own video switcher, there isn't much info
available. All I have is the Datavideo switcher diagram, which the TB5
is designed for:
http://www.drewlahat.com/misc/Datavideo_switcher_Tally_pinout.GIF
Given the right cable, should I be able to connect the TB5 to the
Panasonic directly and suppose everything will work fine, or not
necessarily?
|
|
|
|
Author: Andrew HolmeDate: 20:51 14-03-08
|
|
"Drew" <drorworld@yahoo.com> wrote in message
news:4686af4a-5048-4c85-9a3a-25fd0441b61e@h11g2000prf.googlegroups.com...
> I'm trying to apply a tally light system: a Panasonic video switcher
> that sends a signal, and I want a couple of LEDs to turn on 150ft.
> away whenever that signal is on. That's it.
>
> Whether I'm building it myself or not, I need to understand what the
> switcher does and doesn't handle, so I don't overload any of the
> Panasonic's components - it's a $11,000 device. Here's the information
> I have about its (D-sub15) control output:
> http://www.drewlahat.com/misc/AV-HS400N_tally.GIF
>
> Is it designed to drive LEDs directly, or would you recommend a relay?
That diagram shows it driving an LED (with a series current-setting
resistor) directly.
You could use a relay or an opto-isolator. I would go for the latter.
You'll need a local DC power source either way.
> What should also be in there to protect the unit (diodes)?
A diode could protect against reverse polarity; you could also include
transorbs (transient absorbers) and use a screened cable with the screen
connected to chassis-earth at both ends.
> The signal has to go through 150 ft. of 26 AWG (7x34) Stranded TC
> wire, rated at 38.5 ohm/Mft.
>
> I might be able to use an off-the-shelf tally system - Datavideo TB5
> (http://www.datavideo.us/products/TB_5_main_page.htm). Since it's
> designed to connect to their own video switcher, there isn't much info
> available. All I have is the Datavideo switcher diagram, which the TB5
> is designed for:
> http://www.drewlahat.com/misc/Datavideo_switcher_Tally_pinout.GIF
>
> Given the right cable, should I be able to connect the TB5 to the
> Panasonic directly and suppose everything will work fine, or not
> necessarily?
Looks like it.
They call it an RS232 cable; but it's not RS232. They might as well call it
VGA judging by the D-connectors.
|
|
|
|
1 |
|
|
|
|
Contact | Electronic Portal
|
|
|
